Intel SCB2 - Server Board Motherboard Product Manual Download Page 6

Page: 6 / 108

Intel

Server Board SCB2 Product Guide

Figures

1. Server Board Connector and Component Locations ....................................................... 8

2. Back Panel Connectors .................................................................................................. 9

3. J6A2 Jumper Block for DCD Signal ...............................................................................15

4. J6A2 Jumper Block for DSR Signal ...............................................................................15

Installing the I/O Shield..................................................................................................21

Rearrange the Standoffs................................................................................................22

Installing Server Board Bumpers ...................................................................................23

Installing the Server Board.............................................................................................24

Raising the Locking Bar.................................................................................................25

10. Installing Processors......................................................................................................25

11. Installing the Heat Sink ..................................................................................................26

12. Closing the Locking Lever..............................................................................................27

13. Connecting the Heat Sink Fan .......................................................................................27

14. Installing the Processor Terminator ...............................................................................28

15. Installing Memory ..........................................................................................................29

16. Connecting Cables ........................................................................................................30

17. Installing DIMMs ............................................................................................................32

18. Insert the Processor and Lower the Locking Bar ...........................................................34

19. Installing the Heat Sink ..................................................................................................35

20. Attach the Heat Sink......................................................................................................36

21. Connect the Heat Sink Fan............................................................................................36

22. Installing a Terminator ...................................................................................................38

23. Replacing the Back up Battery.......................................................................................40

24. System Setup Utility Main Window ................................................................................59

25. Platform Event Manager Main Window..........................................................................66

26. Platform Event Paging Dialog ........................................................................................67

27. BMC LAN-Configuration Dialog .....................................................................................68

28. Platform Event Action Dialogs .......................................................................................71

29. Emergency Management Port Dialog ............................................................................72

30. Jumper Locations ..........................................................................................................91

Tables

Server Board Versions.................................................................................................... 7

Server Board Features ................................................................................................... 7

Rear COM2 Port Adapter Pin-out ..................................................................................15

Software Security Features............................................................................................18

Configuration Utilities.....................................................................................................42

Hot Keys .....................................................................................................................42

BIOS Setup Menu Navigation ........................................................................................44

BIOS Setup Menu Display .............................................................................................45

Command Line Format ..................................................................................................80

10.

Configuration Jumper ....................................................................................................91

11.

Post Codes....................................................................................................................92

12.

Power Usage Worksheet 1 ..........................................................................................102

13.

Power Usage Worksheet 2 ..........................................................................................103

Summary of Contents for SCB2 - Server Board Motherboard













































































































Search results

Summary of Contents for SCB2 - Server Board Motherboard

Reviews:

Related manuals for SCB2 - Server Board Motherboard

Brands by name

Popular brands

Intel SCB2 - Server Board Motherboard, Product Manual

Search results

Summary of Contents for SCB2 - Server Board Motherboard

Reviews:

Related manuals for SCB2 - Server Board Motherboard

Brands by name

Popular brands