Intel P4000M Service Manual Download Page 82

Page: 82 / 111

Hardware Installations and Upgrades

Intel

Server Chassis P4000M Service Guide

Replacing the Power Distribution Board for 1200-W
PSUs

WARNING

Hazardous voltage, current, and energy levels are present inside the power supply. There are no

user-serviceable parts inside it; servicing should be done by technically qualified personnel.

Follow instructions in “Replacing the Power Distribution Board for 460-W/750-W PSUs” except

the Power Distribution Board is located at different place in the PDB bracket.

To remove the Power Distribution Board, loosen screws securing the PDB bracket to the

chassis. See letter

. Push the bracket forward to release the latch which secure the bracket

then pull out the bracket from the chassis. See letter

. The figure shows the different PDB

locations for 460-W/750-W PSU and 1200-W PSU.

Figure 112. Removing the PDB for 1200-W PSU

Summary of Contents for P4000M
















































































































Search results

Summary of Contents for P4000M

Reviews:

Related manuals for P4000M

Brands by name

Popular brands

Intel P4000M, Service Manual

Search results

Summary of Contents for P4000M

Reviews:

Related manuals for P4000M

Brands by name

Popular brands