Intel P4000M Service Manual Download Page 34

Page: 34 / 111

Hardware Installations and Upgrades

Intel

Server Chassis P4000M Service Guide

Installing and/or Removing Airduct

NOTE

Airduct may need to be ordered separately. See Configuration Guide of the server board for which airduct

work with your server board. The installation and/or removing airduct steps in below is generic. Please

see your board or system documents for specific instructions about installing and/or removing airduct.

Installing the Airduct

1. Observe the safety and ESD precautions at the beginning of this book.

2. Power down the server and unplug all peripheral devices and the AC power cable.

3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover”.

4. Install the airduct by matching the alignment tabs on airduct and the alignment holes on chassis

bracket.

Figure 31. Installing the Airduct

Summary of Contents for P4000M
















































































































Search results

Summary of Contents for P4000M

Reviews:

Related manuals for P4000M

Brands by name

Popular brands

Intel P4000M, Service Manual

Search results

Summary of Contents for P4000M

Reviews:

Related manuals for P4000M

Brands by name

Popular brands