Intel P4000M Service Manual Download Page 60

Page: 60 / 111

Hardware Installations and Upgrades

Intel

Server Chassis P4000M Service Guide

3. Install the 8x2.5'' Hotswap Hard drives cage. For instructions, see “Installing 8x2.5'' Hotswap Hard

Drive Cage Assembly”.

4. Install the front bezel. For instructions, see “Installing the Front Bezel (Pedestal Only)”.

5. Install the air duct if the air duct is removed. For instructions, see “Installing the Airduct”.

6. Install the chassis cover. For instructions, see “Installing the Chassis Cover”.

7. Plug all peripheral devices and the AC power cable into the server.

8. Power up the server.

Installing Hotswap Hard Drive

Installing 3.5" Hotswap Hard Disk Drive

NOTE

This procedure applies only to the Intel

Server Chassis P4000M family with 3.5'' hotswap hard disk drive

cage configuration.

1. Open the Hotswap HDD door

2. Remove the drive carrier by pressing the green button and opening the lever (see letter

). Then slide the

carrier out (see letter

Figure 70. Sliding the 3.5

HDD carrier out

Summary of Contents for P4000M
















































































































Search results

Summary of Contents for P4000M

Reviews:

Related manuals for P4000M

Brands by name

Popular brands

Intel P4000M, Service Manual

Search results

Summary of Contents for P4000M

Reviews:

Related manuals for P4000M

Brands by name

Popular brands