Intel P4000M Service Manual Download Page 37

Page: 37 / 111

Hardware Installations and Upgrades

Intel

Server Chassis P4000M Service Guide

6. Install the fixed fan in the corresponding fan bracket (see letter

Figure 35. Installing the Fixed Fan

7. Connect fan power cable to the server/workstation board. See the

Quick Start User’s Guide

Service Guide

provided with your Intel

server/workstation board for appropriate connection location.

Removing and Installing the Hotswap Fan

NOTE

This procedure applies only to the Intel

Server Chassis P4000M family with hotswap fan configuration.

Removing the Hotswap Fan

1. Observe the safety and ESD precautions at the beginning of this book.

2. Remove the chassis cover. For instructions, see “Removing the Chassis Cover”.

3. Press latch on fan and pull on handle to remove hotswap fan from chassis.

Figure 36. Removing Hotswap Fan

Summary of Contents for P4000M
















































































































Search results

Summary of Contents for P4000M

Reviews:

Related manuals for P4000M

Brands by name

Popular brands

Intel P4000M, Service Manual

Search results

Summary of Contents for P4000M

Reviews:

Related manuals for P4000M

Brands by name

Popular brands