background image

Bef

Ore 

YO

Begin

2

• read this Guide completely BeFore you begin.  
• disconnect the battery negative terminal while working on the vehicle.

• do not pLaCe tHe KeY FoB in the vehicle with the battery connected and 

the seat airbag wiring disconnected.  doing so will set off the airbag light, 

which must be reset by your dealer.

• aLWaYs check behind panels and components before drilling, cutting, 

or screwing into any part of a vehicle. 

• this guide covers several different vehicle models and options.  some 

steps only apply to certain installations.  steps images are labeled with 
a black bar across the top:

 

-

[6spK OnlY] 

apply only to vehicles equipped with the standard 6 speaker audio system.  

 

-

[hifi/hK OnlY] 

apply only to vehicles equipped with the upgraded 10 speaker hifi and 

harmon kardon audio system.  if the vehicle has tweeters in the a-pillar (near the bottom 

outer corners of the windshield), you have the hifi or hk systems. 

 

-

[suB OnlY] 

apply only if you are installing the integral audio subwoofer system

 

-

[rxx OnlY] 

apply only to the specific model listed.

 

-

if there is no label, the step applies to all installations

 

-

because each kit applies to more than one vehicle, your kit may include extra items.

• are You usinG tHe CorreCt instaLL Guide?  

there are two installa-

tion guides: one for installing the amp in the right-rear of the luggage 
compartment, the other for installing the amp under one of the front 
seats.  this guide is for the underseat amp Mount kit.  (all r57, r58, 
r59, and ‘07-09 r56 JCW vehicles are underseat amp Mount).  Com-
pare the passenger side of your vehicles boot area to the images below. 
if your vehicle looks like the image on the right proceed with this instal-
lation guide.  if not refer to the rear amp Mount installation Guide.

iMpOrtant

 Use Rear Amp Mount guide:

Use this Guide:

Summary of Contents for 2007-2009 R56 JCW


























Reviews: