background image

INSTEON LampLinc Dimmer User’s Guide 

 

Page 16 of 21 

 

ABOUT INSTEON 

Understanding Why an INSTEON Network Is Reliable 

INSTEON messages travel throughout the home via Powerline Carrier (PLC) signals on the existing 
house wiring, and also via wireless Radio Frequency (RF).  As the messages make their way to 
INSTEON devices being controlled, they are picked up and retransmitted by all other INSTEON devices 
along the way.  This method of communicating, called a 

mesh network

, is very reliable because each 

additional INSTEON device helps to support the overall network. 

To further ensure reliability, every INSTEON device confirms that it has received a command.  If an 
INSTEON Controller does not receive this confirmation, it will automatically retransmit the command up to 
five times. 

Further Enhancing Reliability 

As signals travel via the powerline or RF throughout the home, they naturally become 
weaker the farther they travel.  The best way to overcome signals getting weaker is to 
increase the coverage of the mesh network by introducing more INSTEON devices. 

It is possible that some audio-video products, computers, power strips or other electrical 
equipment may attenuate INSTEON signals on the powerline.  You can temporarily 
unplug suspected devices to test whether the INSTEON signal improves.  If it does, then 
you can plug in filters available from Smarthome that will permanently fix the problem. 

Using Smarthome’s Access Points to Upgrade Your INSTEON Network

 

 

Access Points are ideal for improving signal strength and network coverage throughout your home.  In 
addition, two Access Points provide a wireless path for INSTEON signals to travel between the two 
separate electrical circuits, called 

powerline phases

, found in most homes.  Without a reliable method for 

coupling opposite powerline phases, some parts of your home may receive INSTEON signals 
intermittently.  With at least one Access Point plugged into one of the powerline phases, and at least one 
more plugged into the opposite powerline phase, INSTEON powerline signals will be strong everywhere 
in your home. 

Summary of Contents for LampLinc 2456D2






















Reviews: