background image

10 

 

 

Learn to control it properly before first using. 

 

Walk 1 km. constantly for about 15-25 mins. And record the time. Walk 1 km at a speed of 4.8 

km/h (approx. 12 mins). If you are able to do it easily for a few times, you can adjust the speed 
and incline level and exercise for 30 mins to exercise properly.  

 

Don’t overstretch yourself and exercise reasonably. 

CHEST BELT M8 POLAR 

 

In  standby  mode  press  PULSE  button.  The  highest  heart  rate  is  120.  You  can  adjust  the  maximum 
heart  rate  between  80-120.  When  the  heart  rate  is  over  the  maximum  setting,  you  will  hear  the 
warning sound for 3 seconds. After two additional seconds the treadmill speed will reduce by 1 km/h.  

If the heart rate is over maximum settings after 3 minutes, you will hear additional warning sounds for 
3 seconds. After two additional seconds the treadmill speed will be reduced by 1 km/h.  

If the heart rate is over maximum settings after additional 3 minutes, you will hear additional warning 
sounds for 3 seconds. After two additional seconds the treadmill speed will be reduced until it stops.  

 

Pulse transmission is used on the belt. It detects heart rate in real-time. It is water proof. It is made by 
light and durable materials and should last about 2500 hours.  

EXERCISE FREQUENCY 

The target is 3 

– 5 time a week 15 – 60 mins each time. It is better first to elaborate a workout plan 

and  not  to  exercise  only  depending  on  your  will.  It  helps  you  control  your  movements  and  speed  or 
incline adjustment. We recommend not do increase the incline at the initial workout phase.  

WARM-UP PHASE 

NOTE:

 The best way to save your time is to do exercises for 15 

– 20 mins. 

Warm up for 2 minutes at  4.8 km/h and adjust  your speed to 5.3 km/h (5.8 km/h) and continue  your 
workout at these speeds levels for 2 mins. Thereafter you can increase your speed by 0.3 km/h per 2 
mins until you will breath quickly but not difficultly. If your breathing gets difficult, decrease your speed 
by  0.3  km/h.  At  least  reduce  the  speed  for  4  minutes.  If  you  remark,  it  is  difficult  for  you  to  intensify 
your workout by increasing the speed, you can try to increase the incline slowly.  

HEAT CONSUMPTION

 

– It is the real heat consumption. Warm up for 5 minutes at the speed of 4 – 

4.8 km/h and then add 0.3 km/h by 2 minutes (speed increasing). You can exercise for 45 mins at this 
speed  level  as  a  challenge  to  do  your  workout  more  strenuous.  You  can  exercise  for  1  hour  at  this 
speed  while  watching  a  TV  program  and  increase  your  speed  by  0.3  km/h  by  business 
advertisements.  Then  return  to  the  previous  speed  level  when  next  program  starts.  The  heat 
consumption will be more intensive (increased pulse) during the advertisement time. Keep 4 minutes 
to reduce your speed. 

NOTE:

 Wear suitable sports shoes with clean soles. Wear suitable sports clothes. 

PROMPT  WARMING  -UP: 

It  is  better  to  do  some  warm-up  exercises  before  starting  any  workout. 

Stretch  your muscles (5-10 mins) to warm up them. Then  do  warm up workout according to pictures 
below.  Repeat  it  five  times  and  10  seconds  for  each  foot.  Repeat  these  exercises  after  completing 
your workout. 

Summary of Contents for FlatRun IN 18227























Reviews: