background image

 

TECHNICAL DESCRIPTION 

Assembled size (mm) 

1515*770*1010 

Speed range (km/h) 

1-12 

Folded size (mm) 

1581*770*138 

Spec (HP) 

1.25 

Running belt size (mm) 

450*1250 

Input volt (V) 

220-240 

Weight (kg) 

43 

Rating motor (W) 

930 

Max. user weight (kg) 

100 

Operating temperature (°C)  0-28 

LED display 

Speed, Time, Distance, Calories, Pulse 

Safety 

protection, 

advantages 

 

Magnetic safety lock (red). 

 

Overcurrent and overload function set in the microcomputer. 

 

LED screen, clear and clean display, view from any angle  

 

1-12 km/h speed range  

 

Buffer system makes your workout natural and smooth assuring the 

lowest impact for user feet, ankles, joints etc  

 

The over-current protector can continue in function only if manually 

reset. It protects the motor from damaging. 

 

Intelligent explosion-proof circuit can finish working in 0.3 seconds. 

It offers the highest protection. 

 

CONSOLE 

 

Description 

 Distance 

Display  exercise  distance  from  0.00 

– 99.0 when it reaches the maximum it will 

start from 0 again 

Time 

Step 

Time and step switch every 5 seconds 

Time display exercise time, in manual mode it counts from 0:00 to 99:59. When it 
reaches  99:59,  the  treadmill  will  steadily  decrease  the  speed  and  stop.  After  5 
seconds the treadmill will enter standby mode.  

Steps display current exercise steps from 0 to 9999. 

 Calories 

Show  burned  calories  from  0.0  to  999,  after  it  reaches  the  maximum  it  will  start 
from 0.  

 Speed 

Display current speed from 1.0 

– 12.0 km/h 

Summary of Contents for FlatRun IN 18227























Reviews: