background image

25 

 

35 

5/16” x 5/8” Allen bolt 

10 

36 

5/16“ x 1/2” sunken head bolt 

37 

m6 x 15 mm inner hex bolt 

38 

m6 x 10mm hexagon alloy steel bolt 

16 

39 

m6 x 12 mm hex bolt 

40 

5/16” x 1/4” set  

41 

1/

2” washer 

42 

3/8“ washer 

43 

M6 spring washer 

44 

M6 rubber gasket 

45 

1/2” nylon nut 

46 

3/8” nylon nut 

47 

1/2“ nut 

13 

48 

5 mm hex key 

49 

4 mm hex key 

MAINTENANCE AND CLEANING  

 

Check the device regularly before each use. Make sure all bolts are properly tightened. 

 

Check cable guidance. 

 

Make sure that the weight selection pin is properly inserted and not damaged. 

 

You can adjust the height of the cable holder with a pin. 

 

Clean the frame with a damp cloth. 

 

Check the condition of the cables. 

 

Lubricate the adjustable parts and guide rods. 

ENVIRONMENT PROTECTION 

After the product lifespan expired or if the possible repairing is uneconomic, dispose it according to the 
local laws and environmentally friendly in the nearest scrapyard. 

By  proper  disposal  you  will  protect  the  environment  and  natural  sources.  Moreover,  you  can  help 
protect  human  health.  If  you  are  not  sure  in  correct  disposing,  ask  local  authorities  to  avoid  law 
violation or sanctions. 

Don’t put the batteries among house waste but hand them in to the recycling place. 

TERMS AND CONDITIONS OF WARRANTY, WARRANTY CLAIMS 

General Conditions of Warranty and Definition of Terms 

All  Warranty  Conditions  stated  here  under  determine  Warranty  Coverage  and  Warranty  Claim 
Procedure. Conditions of Warranty and Warranty Claims are governed by Act No. 89/2012 Coll. Civil 
Code,  and  Act  No.  634/1992  Coll.,  Consumer  Protection,  as  amended,  also  in  cases  that  are  not 
specified by these Warranty rules. 

The seller is SEVEN SPORT s.r.o. with its registered office in 

Strakonická street 1151/2c, Prague 150 

00,  Company  Registration  Number:  26847264,  registered  in  the  Trade  Register  at Regional  Court  in 
Prague, Section C, Insert No. 116888. 

Summary of Contents for 23283




























Reviews: