background image

 

 

3.Safety 

 

General safety rules 

 

1.

 

Before starting, checks on  the tractor and the machine must be 
carried  out  as  regards:  functionality,  road  safety,  accident 
prevention rules. 

2.

 

Together  with  the  operating  and  maintenance  rules  for  the 
machine  it  is  necessary  to  consider  general  health  and  security 
rules and warnings. 

3.

 

Before starting it is mandatory to know everything regarding the 
equipment  and  operating  of  the  machine.  Reading  instructions 
among operating is too late. 

4.

 

Security and warning decals on the machine are very important. 
Respect them always. 

5.

 

Even when using the machine correctly, stones or other objects 
may be thrown on a long distance. Therefore nobody must stand 
within  the  danger  area.  Special  attention  must  be  paid  when 
working near roads or buildings. 

6.

 

Use tractor with the cabin. 

7.

 

Whenever using public roads, respect traffic rules. 

8.

 

Never wear loose or fluttering clothes. 

9.

 

Keep the machine clean to avoid fire danger. 

10.

 

Before starting check the surrounding area for the likely presence 
of children and/or animals. 

11.

 

Never carry passengers on the machine. 

12.

 

At connecting the machine on the tractor put a support foot into 
the working position (up). After removal put the support foot into 
the standing position (down). Take care about the stability of the 
machine when it is removed. 

13.

 

Never  overload  the  machine  and  the  tractor.  Use  the  ballast  if 
necessary. 

14.

 

 Start  the  machine  only  if  all  guards  of  the  machine  are  fit  on 
proper places . 

15.

 

It is forbidden to stand in the range of operating of the machine. 

16.

 

Do not enter the working zone of the PTO shaft. It is dangerous to 
approach the rotating parts of the machine.  

Summary of Contents for DUPLEX 800









































Reviews: