INNOVATECH PRODUCTS & EQUIPMENT CO, INC. .
Copyright © 2008 Innovatech Products & Equipment Co., Inc. All Rights Reserved.
21
Blade Selection Guide
Part # Blade Description Material
81-0051
4 X 9 X .074
81-0052
4 X 9 X .074 W/ NOTCH
81-0053
4 X 9 X .074 W/ NOTCH SD
vct, vat, elastomerics, rescrape glue
81-0054
4 X 9 X .092
81-0055
4 X 9 X .092 W/ NOTCH
81-0056
4 X 9 X .092 W/ NOTCH/SD
vct, vat, elastomerics, rescrape glue, wood,
ceramic thinset
81-0057
4 X 13 X .074
81-0058
4 X 13 X .074 W/ NOTCH
vct, vat, elastomerics, rescrape glue, wood,
ceramic thinset
81-0059
4 X 13 X .074 W/ NOTCH/SD
carpet, vinyl, rubber
81-0060
4 X 13 X .092
81-0061
4 X 13 X .092 W/ NOTCH
vct, vat, elastomerics, rescrape glue, wood,
ceramic thinset
81-0062
4 X 13 X .092 W/ NOTCH/SD
carpet, vinyl, rubber, elastomerics
81-0063
4 X 18 X .074
81-0064
4 X 18 X .074 W/ NOTCH
vct, vat, carpet clean up, rescrape glue
81-0065
4 X 18 X .074 W/ NOTCH/SD
carpet, vinyl, rubber
81-0066
4 X 18 X .092
81-0067
4 X 18 X .092 W/ NOTCH
vct, vat, elastomerics, rescrape glue,
81-0068
4 X 18 X .092 W/ NOTCH/SD
carpet, vinyl, rubber
81-0069
4 X 26 X .074
81-0070
4 X 26 X .074 W/ NOTCH
vct, vat, carpet clean up, rescrape glue
81-0071
4 X 26 X .074 W/ NOTCH/SD
carpet, vinyl
81-0072
4 X 26 X .092
vct, vat, elastomerics, rescrape glue,
81-0073
4 X 26 X .092 W/ NOTCH
wood, ceramic, thinset
81-0074
4 X 26 X .092 W/ NOTCH/SD
carpet, vinyl
81-0079
6 X 18 X .092 W/ NOTCH
double-layered tile, carpet
81-0081
6 X 26 X .092
carpet, ceramic tile, double-layered vct, wood
81-0082
4 1/2 X 10 X .125
81-0084
4 1/2 X 13 X .125
81-0086
4 1/2 X 26 X .125
81-0088
9 X 26 X .125 W/ NOTCH
ceramic thinset, double-layered vct, wood
83-0002
Large tile tooth
83-0001
Milled large tile tooth
epoxy, urethane, mosaic tile, quarry tile,
pavers porcelain, wood
NOTE:
Blade selection depends entirely upon the material to be removed and the type of adhesive used
to adhere the floor covering or coating to the concrete. The tougher the material, the smaller blade will be
more effective in removing the material or adhesive.
Notched self-dicing (SD) blades can be used to ditch (skip rows) the material or using only one side (not
skipping rows). If a blade smaller than 9 inches is required to successfully remove material, it is
suggested that a 9 or 13 inch blade be cut down, leaving the blade a full 9 or 13 inches where it will be
clamped into the jaw.