manualshive.com logo in svg

Innovatech Teerminator-2000, Operation And Maintenance Manual

Share
Download
Innovatech Teerminator-2000 Operation And Maintenance Manual Download Page 33

33 

TERMINATOR® OPERATION AND MAINTENANCE MANUAL 

 Blade Selection Guide

 

 

Part #

 

Blade Description

 

Material

 

 

 

 

 

  

TW-1001 

4 X 9 X .074  

TW-1001-S/N 

4 X 9 X .074   W/ NOTCH 

vct,vat, elastomerics, rescrape glue 

TW-1001-SSD 

4 X 9 X .074   W/ NOTCH SD 

  

TW-1005 

4 X 9 X .092   

TW-1005-S/N 

4 X 9 X .092   W/ NOTCH 

TW-1005-SSD 

4 X 9 X .092   W/ NOTCH/SD 

vct,vat, elastomerics, rescrape glue, wood, 
ceramic thinset 

TW-1010 

4 X 13 X .074   

TW-1010-S/N 

4 X 13 X .074   W/ NOTCH 

vct,vat, elastomerics, rescrape glue, wood, 
ceramic thinset 

TW-1010-SSD 

4 X 13 X .074   W/ NOTCH/SD 

carpet, vinyl, rubber 

TW-1015 

4 X 13 X .092   

TW-1015-S/N 

4 X 13 X .092   W/ NOTCH 

vct,vat, elastomerics, rescrape glue, wood, 
ceramic thinset 

TW-1015-SSD 

4 X 13 X .092   W/ NOTCH/SD 

carpet, vinyl, rubber, elastomerics 

TW-1020 

4 X 18 X .074   

TW-1020-S/N 

4 X 18 X .074   W/ NOTCH 

vct,vat, carpet clean up, rescrape glue 

TW-1020-SSD 

4 X 18 X .074   W/ NOTCH/SD 

carpet, vinyl, rubber 

TW-1025 

4 X 18 X .092   

TW-1025-S/N 

4 X 18 X .092   W/ NOTCH 

vct,vat, elastomerics, rescrape glue, 

TW-1025-SSD 

4 X 18 X .092   W/ NOTCH/SD 

carpet, vinyl, rubber 

TW-1030 

4 X 26 X .074   

TW-1030-S/N 

4 X 26 X .074   W/ NOTCH 

vct,vat, carpet clean up, rescrape glue 

TW-1030-SSD 

4 X 26 X .074   W/ NOTCH/SD 

carpet, vinyl 

TW-1035 

4 X 26 X .092   

vct,vat, elastomerics, rescrape glue, 

TW-1035-S/N 

4 X 26 X .092  W/ NOTCH 

wood, ceramic, thinset 

TW-1035-SSD 

4 X 26 X .092  W/ NOTCH/SD 

carpet, vinyl 

TW-2025-S/N 

6 X 18 X .092 W/ NOTCH 

double-layered tile, carpet 

TW-2035-S/N 

6 X 26 X .092 

carpet, ceramic tile, double-layered vct, 
wood 

TW-3005 

4 1/2 X 10 X .125 

TW-3015 

4 1/2 X 13 X .125 

TW-3035 

4 1/2 X 26 X .125 

TW-3045-S/N 

9 X 26 X .125 W/ NOTCH 

ceramic thinset, double-layered vct, wood 

AC2-029 

small tile tooth 

AC2-019 

large tile tooth 

epoxy, urethane, mosaic tile, quarry tile, 
pavers porcelain, wood 

 

NOTE:  Blade selection depends entirely upon the material to be removed and the type of adhesive used to 
adhere the floor covering or coating to the concrete.  The tougher the material, the smaller blade will be 
more effective in removing the material or adhesive.   
 
Notched self-dicing (SD) blades can be used to ditch (skip rows) the material or using only one side (not 
skipping rows).  If a blade smaller than 9 inches is required to successfully remove material, it is suggested 
that a 9 or 13 inch blade be cut down, leaving the blade a full 9 or 13 inches where it will be clamped into 
the jaw.  

 

 

 
 

Summary of Contents for Teerminator-2000



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands