manualshive.com logo in svg

Innovatech Teerminator-2000, Operation And Maintenance Manual

Share
Download
Innovatech Teerminator-2000 Operation And Maintenance Manual Download Page 31

31 

TERMINATOR® OPERATION AND MAINTENANCE MANUAL 

Terminator® Tune-up Specs/H20 – II (electronic ignition) 

 

   

 

 

 

 

 

⇓

 

Timing:    

3-8

°

 degrees                |        |       |       |       | 

                                                   0

°

    5

°

    10

°

    15

°

   20

°

 

 
 
RPM’s: 

 

 

 idle 900 to 1,000 rpm’s 

 
 

Spark Plug Gap:          

.031

" to 

.035

" 

  

 

 

    

 Bosch type B4ES, BPR4ES 

Check spark plug electrodes for pitting.  If pitting is present check LPG regulator for leaking gasket. 
[pitted spark plug electrodes are a indication of moisture in fuel] 
 
 
Air Gap:    

 

 

0.35 mm

 to 

0.45 mm

 

 

 

 

 

0.0138"

   to  

0.0177"

 

 
 

Measure air gap between signal rotor and pickup assembly. 

 

 

 
Carb:  idle adjustment; back out adjusting screw 

2½

 to 

3

 turns 

            Lean/Rich mixture adjustment under air horn should be set with  
            a gas analyzer, allowing for the lowest emissions at the highest 
            peak rpm performance. ( snap acceleration test ) 

 

here   to    here 

 
                                                                  

               

⇓

         

⇓

 

R

 \  

  \

    

| 

   /    /

L

 

 
Lean/Rich setting depends upon emission readings. It is recommended that a four or five gas analyzer 
be used in making this adjustment.  Each time after adjusting the mixture wait 6 to 15 seconds before 
reading the analyzer. 
 
If problems still persist, the carburetor should be taken apart and cleaned. The venturi plunger should 
move up and down freely without sticking. Check propane regulator.  
 
 

Innovatech Products & Equipment Co., Inc. 
19722 144

th

 AVE. NE 

WOODINVILLE, WA     98072           
Phone: 1-425-402-1881              FAX: 1-425-402-8547 
1-800-267-6682 
Email:  [email protected] 

 

 

 

 

 

 

 

 

 

 

TuneII.doc

 

 

 

 

Summary of Contents for Teerminator-2000



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands