background image

17 

 

 

Appendix A: Limited Warranty 
 

LIMITED WARRANTY 
Innovate stands behind the quality of its products. Innovate makes the following warranty to 
purchasers of its products: All new Innovate products carry a one year warranty from the date of 
purchase. If proof of purchase cannot be provided, warranty will be determined by date of 
manufacture. 

When Warranty Void 
This warranty shall terminate and Innovate shall have no obligation pursuant to it if (i) your 
Innovate product has been modified or repaired in a manner not previously authorized by 
Innovate in writing, (ii) the identification markings on your Innovate product have been removed, 
defaced, or altered; (iii) your Innovate product was subjected to accident, abuse, shipping 
damage, or improper use; (iv) your Innovate product was not used or configured as specified in 
the product manual; or (v) your Innovate product was subjected to operating conditions more 
severe than those specified in the product manual. 

Exclusions From This Warranty 

Oxygen Sensors are excluded from this warranty.

 

Repairs Under This Warranty 
In the unlikely event that your Innovate hardware product should prove defective during the 
warranty period, contact Innovate Customer Support at 
http://www.innovatemotorsports.com/rma_form.php for a return material authorization (RMA). 
Products returned for service must be securely packed to prevent damage and shipped charges 
pre paid, along with proof of purchase and the return material authorization number, to the 
Innovate repair location as instructed by Customer Service. Innovate within a reasonable 
amount of time from its receipt of your product so shipped, will ship to you, at its option, the 
repaired product or a new or reconditioned product of comparable or greater specified 
functionality. All repaired or replacement products shall be warranted for the remainder of the 
original product warranty.  

Disclaimer 
INNOVATE MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO 
YOUR INNOVATE PRODUCT OTHER THAN THE LIMITED WARRANTY SET FORTH ABOVE. 
No Innovate dealer, agent, or employee is authorized to make any modification, extension, or 
addition to this warranty, unless enforceable or unlawful under applicable law, INNOVATE 
DISCLAIMS ALL IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF 
MERCHANTABILITY, NONINFRINGEMENT, AND FITNESS FOR A PARTICULAR PURPOSE, 
AND THE LIABILITY OF INNOVATE, IF ANY, FOR DAMAGES RELATING TO ANY 
ALLEGEDLY DEFECTIVE PRODUCT SHALL UNDER ANY TORT, CONTRACT, OR OTHER 
LEGAL THEORY BE LIMITED TO THE ACTUAL PRICE PAID FOR SUCH PRODUCT AND 
SHALL IN NO EVENT INCLUDE INCIDENTAL, CONSEQUENTIAL, SPECIAL, OR INDIRECT 
DAMAGES OF ANY KIND EVEN IF INNOVATE IS AWARE OF THE POSSIBILITY OF SUCH 
DAMAGES. Some states do not allow limitations on how long an implied warranty lasts or the 
exclusion or limitation of incidental or consequential damages, so the above limitations or 
exclusions may not apply to you. 

 

 

Summary of Contents for PSN-1



















Reviews: