Innovate Motorsports PSN-1 User Manual Download Page 13 | Manualshive

Page: 13 / 18

background image

13

checkbox to turn the solenoid control ON/OFF. Default setting is Valet
mode OFF.

Logworks 3 & LM Programmer Software Package

4

The PSN-1 can be connected directly to your Windows computer to log and
analyze data with the Logworks software or to configure with LM
Programmer. The software is a free download on the Innovate Motorsports’
support section of the website.

4.1

Download and Install the Logworks 3 Software

1.

Open your web browser and go to the following URL:

http://www.innovatemotorsports.com/support.php

2.

The LogWorks 3 software download will be the very first thing on the
page under the heading Software, click the link to download the
software.

3.

Double click on the Logworks 3 installer previously downloaded from the
support section of the Innovate Motorsports web site.

4.

The installer will start, follow the prompts to install the software.

5.

Once the software has been installed, the LogWorks software, LM
Programmer, manuals, and tools can then be located by navigating
through Start->Programs->LogWorks3.

4.2

LM Programmer

LM Programmer is used to configure settings on your PSN-1.

1.

Connect the OUT port of the PSN-1 to the provided serial
programming cable. Connect the other end of the serial
programming cable to your computer. If your computer does not
have a serial port, you can purchase a USB to Serial adapter from
Innovate Motorsports (P/N 3733) or use any USB to serial adaptor
that includes drivers. Make sure that nothing is connected to the IN
port of the PSN-1

2.

Power up the PSN-1.

3.

Launch LM Programmer. The LM Programmer application can be
launched from

Start->Programs->LogWorks3->LM Programmer

from

the Windows task bar.

4.2.1

Programming Analog Output

Connect the PSN-1 to the computer and launch LM Programmer. Select the
Analog Output tab. The analog output configuration screen shows voltage
versus Lambda for the analog output. The graph display is automatically
scaled to the selected voltages values. The configuration screen allows the
user to specify a minimum and maximum lambda or A/F value to a
corresponding voltage range.

«
...
11
12
13
14
15
...
»

Summary of Contents for PSN-1



















Reviews:

No comments

Related manuals for PSN-1

Brand: Valore Pages: 4

Brand: GE Pages: 2

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 14

Brand: Panasonic Pages: 30

Brand: ECO Sensors Pages: 2

Brand: Samsung Pages: 88

Brand: Samsung Pages: 215

Brand: AbleNet Pages: 9

Brand: Eclipse Pages: 6

Brand: Jeep Pages: 673

Brand: Keis Pages: 2

Brand: Darimo Pages: 2

Brand: K&M Pages: 3

Brand: Öhlins Pages: 2

Brand: Mazda Pages: 527

IMI SENSORS EX640B61

Brand: PCB Piezotronics Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands