manualshive.com logo in svg

Innomag U-mag Series, Installation Operation & Maintenance, Page: 40 / 56

Share
Download
Innomag U-mag Series Installation Operation & Maintenance Download Page 40

Attaching  the  Honda  engine 

requires  a  special  mounting 

plate.

Section R - Honda Engine Mounting (Assembly)

Page 40

8mm or 5/16” hex key

Adjustable wrench

3/16” (NEMA) or 5mm 

(IEC) T-handle hex key

Tools Needed

þ
þ

Insert  and  tighten  the  (4)  bolts 

attaching  the  adapter  to  the  the 

mounting plate.

þ

Remove  the  metal  plug  from  the 

top  of  the  adapter  and  align  the 

bolt  holes  with  the  holes  on  the 

mounting plate.

Insert and tighten the (4) socket 

head  cap  screws  connecting  the 

mounting plate to the motor.

Center the mounting plate on the  

motor and align the holes.

A

B

Dowel Pins

Note  the  placement  of  the  set 

screws  in  relation  to  the  dowel 

pins before installation.

Align the  key  groove  on  the  mo-

tor  shaft  with  the  row  of  dowel 

pins on the outer magnet assem-

bly. (Adapter not shown above for 

demonstration purposes)

Summary of Contents for U-mag Series

























































Reviews:

No comments