Innomag U-mag Series Installation Operation & Maintenance Download Page 4

Page: 4 / 56

Section A - Safety

For your protection, and the protection

of others, learn and always follow the safety

rules outlined in this booklet. Observe warning

signs on machines and act accordingly. Form

safe working habits by reading the rules and

abiding by them. INSTALLATION, OPERATION

AND MAINTENANCE MUST BE DONE BY THOR-

OUGHLY QUALIFIED PERSONNEL IN STRICT

ACCORDANCE WITH THIS MANUAL AND MUST

COMPLY WITH ALL LOCAL, STATE AND FEDER-

AL CODES. Keep this booklet handy and review

it from time to time to refresh your understand-

ing of the procedures.

Innovative Mag-Drive has designed this

pump for safe and reliable operation. However,

like any mechanical device, the proper and safe

performance of this equipment depends upon

using sound and prudent operating, mainte-

nance and servicing procedures performed by

properly trained personnel. Instructions and

safety procedures contained herein must al-

ways be followed. As such, Innovative Mag-

Drive shall not be liable for any damages or

delays caused by failure to observe any instruc-

tions or warnings in this manual.

The use of the word “DANGER” always signi-

fies an immediate hazard with a high likelihood

of severe personal injury or death if instruc-

tions, including recommended precautions,

are not followed.

The use of the word “MAGNETIC” indicates the

persistent presence of a magnetic field. Such

fields present immediate danger to individu-

als having electronic medical devices, metallic

heart valves, metallic prosthetics or metallic

surgical clips.

The use of the word “WARNING” signifies the

presence of hazards or unsafe practices which

could result in severe personal injury or death

if instructions, including recommended precau-

tions, are not followed.

The use of the word “CAUTION” signifies pos-

sible hazards or unsafe practices which could

result in minor injury, product or property dam-

age if instructions, and recommended precau-

tions are not followed.

MAGNETIC

Safety First

DANGER

WARNING

CAUTION

Page 4

Summary of Contents for U-mag Series

























































Search results

Summary of Contents for U-mag Series

Reviews:

Innomag U-mag Series, Installation Operation & Maintenance, Page: 4 / 56

Search results

Summary of Contents for U-mag Series

Reviews: