background image

LT6387 Iss 4 (05/14) 

 

 

880 FL Users Instructions

 

SECTION TWO Operating the Appliance Continued

 

LOW BATTERY INDICATION (APPLIANCE) 

If  you  hear  a  repeated  ‘bleep’  sound  come  from  the  appliance  this  indicates  the  appliance  battery 
pack is low and should be changed. If this is ignored the system will go into a lock out mode, which 
will not allow the appliance to be use until a new set of batteries are loaded.  

NOTE:

 The appliance cannot be used when the battery is completely discharged. 

 

TO REPLACE APPLIANCE BATTERIES (6 High Power Alkaline C 1.5V) 

a.  Remove the fireplace frame covers which are held in place with magnets. 
b.  Lift out the air grill cover from the bottom of the frame assembly. 

c.

 

The  battery  power  pack  holder  is  located  in  a  compartment  at  the  left  hand  side  of  the  burner. 
Carefully lift the battery holder out of the compartment and replace the six high power alkaline C 
batteries  as  a  complete  set. 

WARNING,  batteries  will  overheat  if  fitted  incorrectly,  when 

fitting the batteries ensure that they are fitted as per the marking on the rear of the holder 
(i.e. minus of battery against spring).

 

e. Once the new batteries are loaded the fire will continue to bleep until re-set. Press the ON / OFF 
key for at least 2 seconds, on release a bleep sound be heard and the ignition process will start. If the 
fire continues to bleep this may indicate a loose connection or badly loaded batteries. 

 
 
 

 

 
 
 
 

*Important : If the fire burner or pilot is extinguished for any reason, do not attempt to re-light 
the pilot for at least 3 minutes.

 

 
880 FL Users Instructions 

SECTION THREE Cleaning

 

 

Warning: -  

Before you clean any part of the appliance ensure that  the 
appliance is turned off and cold. 

CLEANING: PILOT ASSEMBLY 

(Before cleaning ensure that the appliance is turned off and 
cold)  
In  some  instances  you  may  experience  ignition  problems 
even  when  the  appliance  is  new.  This  may  be  due  to  the 
aeration  hole  in  the  pilot  body  being  partial  blocked  with 
dust,  pet  hairs,  or  other  foreign  matter.  The  source  of  this 
debris  could  be  such  things  as  carpet  fibres,  decorating  or 
pet etc. 
 
 
 
 
 
 
 
 
 

Summary of Contents for 880FL









































Reviews: