Infineon TRAVEO T2G family CYT4D Series Page 8 Manual Download

Page: 8 / 80

Application Note

8 of 80

002-26071 Rev. *B

2021-09-07

Clock configuration setup in TRAVEO™ T2G family CYT4D series MCUs

Clock system for TRAVEO™ T2G family MCUs

Figure 4

shows details of the peripheral clock divider #0.

These MCUs need a clock to each peripheral unit (say, the serial communication block (SCB), the timer,
counter, PWM (TCPWM), and so on) and its respective channel. These clocks are controlled by their respective
dividers.

This peripheral clock divider #0 has many peripheral clock dividers to generate the peripheral clock (PCLK). See
the

datasheet

for the number of dividers. The output of any of these dividers can be routed to any peripheral.

Note that dividers already in use cannot be used for other peripherals or channels.

PCLK

Clock divider

8.0

CLK_PERI

PERI_DIV_8_CTL register, INT8_DIV

bit

Clock divider

16.0

PERI_DIV_16_CTL register,

INT16_DIV bit

Clock divider

16.5

PERI_DIV_16_5_CTL register,

FRAC5_DIV bit & INT24_DIV bit

PERI_CLOCK_CTL register,

TYPE_SEL bit & DEV_SEL bit

9 dividers

16 dividers

7 dividers

124 multiplexers

Clock

Generation

Clock divider

24.5

PERI_DIV_24_5_CTL register,

FRAC5_DIV bit & INT24_DIV bit

3 dividers

Clock enable multiplexing

Figure 4

Block diagram for the peripheral clock divider #0

CLK_TRC_DBG

Clock input to the CPUSS (DEBUG).

Divider

Divider has a function to divide each clock. It can be configured from 1 division
to 256 divisions.

Clock divider8.0

Divides a clock by 8

Clock divider16.0

Divides a clock by 16

Clock divider16.5

Divides a clock by 16.5

Clock divider24.5

Divides a clock by 24.5

Clock enable multiplexing

Enables the signal output from the clock divider

Clock generator

Divides the CLK_PERI based on the clock divider

Summary of Contents for TRAVEO T2G family CYT4D Series

















































































Search results

Summary of Contents for TRAVEO T2G family CYT4D Series

Reviews:

Related manuals for TRAVEO T2G family CYT4D Series

Brands by name

Popular brands

Infineon TRAVEO T2G family CYT4D Series, Manual

Search results

Summary of Contents for TRAVEO T2G family CYT4D Series

Reviews:

Related manuals for TRAVEO T2G family CYT4D Series

Brands by name

Popular brands