Impax 2000 Manual Download Page 52 | Manualshive

Page: 52 / 55

background image

Chapter 9 - Specifications and Drawings

SPECIFICATIONS

Controller type: Microprocessor-controlled monitoring and control system for forming

machines.

Measuring System: Force and pressure sensing by piezoelectric transducers; typical size 1-1/8

inch diameter by 1/8 inch thick, or less. Output range: .4 to 200 volts.

Interpreted by 8-bit analog-to-digital converter.

Timing System: Parts counting and measurement timing by non-contact metal detecting

switches on cams or other machine parts. 10-volt output pulse.

Operator Controls
and displays: At machine: “RESET” button and red status light.
At console: Alphanumeric display for measurement and messages, push-

button controls, and Supervisor Keylock to protect settings.

Machine Control: Four relays, operating independently. Immediate, timed, or cycled delay.

Each rated 8 amps, 250 volts AC maximum. May be used to stop machine,

feed, output diverter, or other accessories.

Power
Requirements: 115 volts at 1 amp or 230 volts at ½ amp, 50/60 Hz AC. IMPAX is protected
against surges and motor interference.

Dimensions: Satellite Box: 8" H x 6" W x 4" D
Control Console: 11-3/4" H x 10-3/4" W x 9" D

Satellite Cable: multi conductor, oil resistant covering, 10 foot length
Console weight: Approx. 30 lbs
Distance from IMPAX to machine: Recommended maximum of 20 feet

Environmental
Protection:

Satellite Box and fittings are sealed to NEMA 13. Resistant to oil, heat, and

vibration.

Control Console: Keyboard and case are resistant to oil, smooth and easy to clean. Withstand
extremes of temperature and humidity. Resistant to static electrical
discharge.

Battery: Ni Cad - rated for 6-8 year life.

«
...
50
51
52
53
54
...
»

Summary of Contents for 2000
























































Reviews:

No comments

Related manuals for 2000

MultiSync XG-1352

Brand: NEC Pages: 38

Brand: Samsung Pages: 100

SyncMaster 400UXn-UD

Brand: Samsung Pages: 25

Brand: Acer Pages: 15

Brand: Interlogix Pages: 84

LC-VT1503 Series

Brand: Canvys Pages: 12

Brand: Barco Pages: 12

Brand: Akron Pages: 2

Brand: V7 Pages: 1

Brand: IBM Pages: 41

Brand: Safety 1st Pages: 8

UltraView iAP1000AV

Brand: I-Tech Pages: 1

MultiSync FE772M

Brand: NEC Pages: 50

Brand: Rapid Controls Pages: 55

Brand: ReliOn Pages: 52

BABYTOUCH 29763Z

Brand: Summer Pages: 12

Brand: Boss Audio Systems Pages: 3

Brand: I-Inc Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands