Impax 2000 Manual Download Page 50 | Manualshive

Page: 50 / 55

background image

47

Press Enter/Yes

.

The IMPAX is now back to the “DIAGNOSTICS” display.

Checksum and Memory Test:

Press the number 3 key. The display shows “BYPASS IMPAX?”.

Press the Enter/Yes

key. (Note: When the IMPAX is bypassed there is

no machine protection.)

The display will show two or three four digit characters, these four digit characters are the
checksums of the software loaded into EPROMS on the CPU board.

Press Enter/Yes. The display shows “BLOCK 0 GOOD”. This is a self test that checks the
blocks of RAM on the CPU board.

Keep pressing Enter/Yes to check all the blocks of memory. When all the memory is tested the
IMPAX will go back to the “DIAGNOSTICS” display.

If you choose not to bypass the IMPAX by pressing Next/No at the

“

BYPASS IMPAX?”

prompt, the IMPAX will go back to the “DIAGNOSTICS” display.

Light, Relay, and Display Test:

Press the number 4 key. The display shows “BYPASS IMPAX?”.

Press the Enter/Yes

key. The display now shows “5-GRN 6-YL 7-RED”.

Pressing the number 1

,

2

,

3

,

or 4

key will activate relays 1, 2, 3, or 4 respectively. Pressing

the number 5

,

6

,

or 7 key will activate the green, yellow, or red lights respectively. (Note each

time a number is pressed the previous relay or light is turned off.

Press Enter/Yes. The display shows

“ * ”.

Press Next/No to step through the first part of the display test, the asterisk will shift through each
segment of the display each time the

Next/No

key is pressed. When each segment has been

tested a “O

”

will appear in the first segment of the display, pressing

Next/No

will again shift the

“O”

through each segment.

Press Enter/Yes to step to the next display test. The screen will now show a variety of characters.
Continue to press Next/No, a variety of symbols, numbers, and letters will scroll across the
screen. To end this test press Enter/Yes

.

The display now shows

“

DIPS- 00 or DIPS- 00000000

”

.

Press Enter/Yes. The IMPAX is now back to the “DIAGNOSTICS” display.

«
...
48
49
50
51
52
...
»

Summary of Contents for 2000
























































Reviews:

No comments

Related manuals for 2000

Brand: Mackie Pages: 39

9'' TFT LCD COLOR MONITOR

Brand: Eonon Pages: 12

Brand: Vicon Pages: 24

Brand: XP-PEN Pages: 12

Brand: Luminator Pages: 34

Brand: Monoprice Pages: 18

Brand: FEC Pages: 22

Brand: Farenheit Pages: 19

Brand: SMARTBABY Pages: 32

Brand: FDT Pages: 22

Brand: Speco Pages: 1

Brand: 7starlake Pages: 10

Brand: Sanitas Pages: 52

Brand: Van Mechelen Pages: 19

Brand: voxicon Pages: 11

IDK-1110WR-50WSA1

Brand: Advantech Pages: 35

Brand: Sencor Pages: 14

Brand: Ametek Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands