Impax 2000 Manual Download Page 48

Page: 48 / 55

Chapter 8 - Diagnostics

DEFINITION OF DIAGNOSTIC FEATURES FOR ALL IMPAX

SYSTEMS

Getting Into Diagnostics:

Turn the

SUPERVISOR'S KEY

to the on or horizontal position. (Note if the IMPAX is

currently in a force or tolerance screen the Clear key will have to be pressed to get back to a
quantity screen.)

Press Function

(#)

. The display will show “SELECT FUNCTION”.

Press the number 4 key. (Function 4 selects the diagnostics mode.) The display will show

“

ACCESS

_”

Enter the access code by pressing the numbers 5, 6, 8, 6, then press Enter/Yes, the display will
show

“

REDEFINE?

”.

This is asking if you wish to redefine the access code from 5686 to a four

digit number of your choice.

If you answer no by pressing Next/No. The display will show “DIAGNOSTICS”

If you wish to

redefine the access code press Enter/Yes at the

“

REDEFINE

?”

prompt.

The IMPAX will ask

you for a NEW access code. Press any four digit number combination then press

Enter/Yes. The

display now shows “ACCESS

_”

. Press the same four digit code you just entered, then press

Enter/Yes. The display will now show

“DIAGNOSTICS”. You can exit the diagnostics mode at

any time by pressing Clear.

Diagnostic Functions:

Versions' 47.xx, 50.xx, and 57.xx:

Press the number 2 key the IMPAX will display the old communications parameters.
Press the

ENTER/YES

key to step through the various settings. These settings will have no

effect on the IMPAX operation since they are no longer used.

Versions' 48.xx and 58.xx:

Press the number 9

key. If the display shows

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _

, there is nothing being

transmitted or received by the IMPAX unit via the IMPAXNET. If the display has characters on

Summary of Contents for 2000
























































Search results

Summary of Contents for 2000

Reviews:

Related manuals for 2000

Brands by name

Popular brands

Impax 2000, Manual

Search results

Summary of Contents for 2000

Reviews:

Related manuals for 2000

Brands by name

Popular brands