Impax 2000 Manual Download Page 49

Page: 49 / 55

the left and right sides of the screen that are changing rapidly, there is data being transmitted or
received by the IMPAX via the IMPAXNET.

Software Version and Definition Package ID:

Press the number 1

key. The display will show “VERSION XXXXX-XX”, the X's reference the

software version that is in the IMPAX system.

Press Enter/Yes. The display shows “P-X TH-YY D-ZZ”.

refers to the software language in the IMPAX:

is English

is German

is Spanish

is French

is Portuguese

is Italian

refers to the tolerance threshold table:

indicates Standard Limits

indicates Tight Limits

indicates Tighter Limits

refers to the definition package:

is for 1 Die 2 Blow

is for 2 Die 3 Blow or 2D4B

has 2 force line capability

has 3 force line capability

has 4 force line capability

has 5 force line capability

has 6 force line capability

has 7 force line capability

has 8 force line capability

is for Roller

is for 1D2B with shortfeed sensor

is for 2D3B or 2D4B with shortfeed sensor

has shortfeed plus 2 force line capability

has shortfeed plus 3 force line capability

has shortfeed plus 4 force line capability

has shortfeed plus 5 force line capability

has shortfeed plus 6 force line capability

has shortfeed plus 7 force line capability

Summary of Contents for 2000
























































Search results

Summary of Contents for 2000

Reviews:

Related manuals for 2000

Brands by name

Popular brands

Impax 2000, Manual

Search results

Summary of Contents for 2000

Reviews:

Related manuals for 2000

Brands by name

Popular brands