TRADUCTION OF THE ORIGINAL USER’S INSTRUCTIONS
KS450FTeng ED.2011 rev.34
11
If your working process require it, on the unloading side you can choose to use the roller table with manual
measuring system with digital readout (RTL) or the one with digital measuring system and automatic positioning of
the stop (RTP) also.
This last device must be connected to the machine by a special device – ITEM 000910-01 –to sinchronize the
movement of the saw frame within the automatic backwarding of the lenght stop.
Inverter for variable blade speed - ESC - is an accessory which can be installed when manufacturing the saw and
allows the blade to have a variable speed. It can be adjusted by means of a selector located on the control panel.
In case the maximum power supply threshold is exceeded - for example, because of an excessive cutting pressure or
because the blade remains stuck into the material - the Inverter stops the motor. To restore it, the main switch has to
be turned to 0 (OFF), wait for about one minute and then turn it on I (ON).
In the meantime, try to find out the reason that caused the interruption and eliminate it.
Voltage transformer - place it between the electric equipment of the building and the electric supply of the machine. It
allows to work with a different voltage than the standard one (that is 400V / 50 Hz).
Available voltages: 230V, 460V, 500V, 575V.
Minimal lubrication – THE MINIMAL LUBRICATION SYSTEM APPLIED TO THE BANDSAW ALLOW TO ELIMINATE
ALMOST COMPLETELY THE TRADITIONAL COOLANT SYSTEM. THE MATERIAL IS MUCH CLEANER AND
THERE IS NO WASTE/SPILLING OF COOLANT AND WATER, CONTRIBUTING THUS TO PRESERVING NON-
RENEWABLE ENERGY SOURCES AS WELL. IT IS ACTIVE ONLY DURING THE CUT.
IT IS COMPRISED OF A NOZZLE – F00f197m – WITH 3 MICRO-HOLES TO SPREAD THE OIL ON THE BLADE, A
TANK WITH DEVICE TO ADJUST THE OIL FLOW AND ANOTHER TO REGULATE THE AIR PRESSURE. THE
24V LOW TENSION SWITCH ALLOWS TO STOP IT AT ANY TIME AND USE THE NORMAL STANDARD
COOLANT SYSTEM.
Unloading Roller Table RTL with
digital
readout
(Optional):
it
is
comprised of an RTS with the addition of
a measuring device equipped with digital
readout, powered by one size A battery.
It is available in 3- and 6-meter units. To
connect to the right side of the saw.
.
Unloading
Roller
Table
with
motorized positioning RTP (Optional):
it is comprised of the RTS roller table
and a motorized bar-stop. The blade
movement can be synchronized with the
ongoing control of the cutting lengths.
Available in 3- and 6-meter units to be
connected to the right side of the
machine.
Summary of Contents for KS 450 FT
