TRADUCTION OF THE ORIGINAL USER’S INSTRUCTIONS
KS450FTeng ED.2011 rev.34
20
at 0° position, with the sawframe completely lowered, open the hooks of the blade protection structure and move it
upward all the way (if necessary move away the splashguard – picture RI0414, No. 3); check that the blade is close to
the pulleys and well-placed into their guides. You can loosen the forward blade-tensioning screw and adjust the
position of the blade if necessary, then close again the blade protection structure.
A green lamp on the control panel, when on, shows that such structure is properly closed.
If the blade is not appropriately tensioned, proceed as follows:
Turn on the main switch – picture RI0416, No. 2, the WHITE lamp turns on, then push the yellow button – picture
RI0421, No. 6 – for a few seconds. If the blade protection guard is closed, the corresponding green lamp turns on.
Tighten the blade-tensioning screw until the corresponding GREEN light is on. Tighten one-fourth of a round
more to prevent loosening.
The procedure described above has to be carried out also when changing the blade. In this case an accurate cleaning
of all parts in contact with the blade is recommended.
In the following paragraph you will find the full control list.
15 - DESCRIPTIONS OF CONTROLS
The sectioning devices of the external energy are comprised of the power supply pin and socket and/or the main
switch – picture RI0416, No. 2-3 - on the left side of the control box.
The automatic motion of the sawframe takes place within two limits, respectively for start and end of the cut.
By means of a special mechanical device applied on it, the sawframe drops rapidly until just over the
material, then proceeds to cutting, giving the operator the possibility to adjust down-feed speed and power.
At the end of the cut the sawframe stops and lifts thanks to a limit switch.
The control panel includes:
1) General switch - that can be locked - with magnetic and thermal protection for the whole equipment, complete with
minimum tension coil (picture RI0416, No. 2-3)
2) CHECK PANEL: includes function and control lights
3) Emergency: all electrical devices are stopped when it is activated. To restore them, turn the emergency button one-
fourth of a round (picture RI0416, No. 1)
4) Selector to open/close the vice (picture RI0421, No. 10)
5) RED Button for lifting the sawframe (picture RI0421, No. 8):
keep it pushed to lift it;
if pushed during the cutting cycle, the sawframe stops.
6) BLACK Button for lowering the sawframe (picture RI0421, No. 2):
keep it pushed to lower it
7) WHITE button for starting the cutting cycle (picture RI0421, No. 9)
8) Selector for motor blade speed or Potentiometer to drive the Inverter (as Optional=ESC) to modify the blade speed
(picture RI0421, No.3)
9) YELLOW button to start/Reset the hydraulic unit, with automatic shut-down after about ten-fifteen minutes of
inactivity (picture RI0421, No. 6)
11) Hydraulic regulator of the down-feed sawframe speed (picture RI0421, No. 5)
12) Hydraulic regulator of the down-feed sawframe power (picture RI0421, No. 4)
The automatic motion of the sawframe
takes
place
within
two
limits,
respectively for start and end of the cut.
By means of a special mechanical
device applied on it, the sawframe
drops rapidly until just over the
material, then proceeds to cutting,
giving the operator the possibility to
adjust down-feed speed and power. At
the end of the cut the sawframe stops
and lifts thanks to a limit switch: it is
placednear the right side of the tilting
pin.
Rotate by hand the grey lever against
the switch–without unlocking any
screws- to realize the return position.
Summary of Contents for KS 450 FT
