ILMOR MV10 650 Owner'S Manual Download Page 68

Page: 68 / 78

SECTION 9

ILMOR HIGH-PERFORMANCE OWNER’S MANUAL

9-4

Ilmor High-Performance Marine, LLC

On-Board Diagnostics – Marine (OBD-M)

All Ilmor High-Performance Marine engines are equipped with marine on-

board diagnostics to comply with the 2009 California-mandated OBD-M

specification. The Malfunction Indicator Lamp (MIL) or a Check Engine

warning will appear on the dash when emission system problems occur on

the boat.
If the MIL is set due to an emissions-related fault, a Diagnostic Trouble

Code (DTC) will register. The MIL functions to notify the operator that a

problem has occurred so that the owner/operator can arrange for service

as soon as possible. DTCs are stored in the engine control unit memory

and can be retrieved with a diagnostic scan tool or through Diacom PC

Software.
This information about system malfunction assists the service technician

in quickly diagnosing system issues. When the MIL lights, the owner /

operator should contact an authorized Ilmor service center to arrange a

diagnostic scan at the earliest possible opportunity.
The diagnostic scan tool will be connected to the Data Link Connector

(DLC), a flat 6-pin connector. The connector is located adjacent to the port

side fuel rail. Note that the protective DLC cover must be removed prior to

connecting the scan tool.

MV10

MV8-570

Summary of Contents for MV10 650















































































Search results

Summary of Contents for MV10 650

Reviews:

Related manuals for MV10 650

Brands by name

Popular brands

ILMOR MV10 650, Owner'S Manual

Search results

Summary of Contents for MV10 650

Reviews:

Related manuals for MV10 650

Brands by name

Popular brands