ILMOR MV10 650 Owner'S Manual Download Page 66

Page: 66 / 78

SECTION 9

ILMOR HIGH-PERFORMANCE OWNER’S MANUAL

9-2

Ilmor High-Performance Marine, LLC

Emissions Control System Information

Emission Control System related components for all engines having the

Emission Control Information label will be acronized as follows: positive

crankcase ventilation (PCV), sequential multiport fuel injection (SFI),

naturally aspirated (NAT), On-Board Diagnostic – Marine (OBD-M),

low-permeation fuel line (HOSE), electronic throttle control (ETC) and

electronic engine control (electronic EC).

Star Label

Beginning January 1, 2009, any boat sold or registered in California must

have a Star Label affixed to the port side of the hull either forward or aft of

the vessel registration as shown in the illustration below.

Star Label Location

A Star Label is also placed on the heat exchanger of each certified Ilmor

High-Performance Marine, LLC engine. All Ilmor High-Performance

Marine engines have a Three Star – Ultra Low Emission rating. This

indicates that the engine has sixty five percent (65%) lower emissions

than One Star – Low Emission engines. The Three Star Label identifies the

engine as meeting the California Air Resources Board’s sterndrive/inboard

marine engine Tier 3 exhaust emissions standards.

Three Star - Ultra Low Emissions Label

Summary of Contents for MV10 650















































































Search results

Summary of Contents for MV10 650

Reviews:

Related manuals for MV10 650

Brands by name

Popular brands

ILMOR MV10 650, Owner'S Manual

Search results

Summary of Contents for MV10 650

Reviews:

Related manuals for MV10 650

Brands by name

Popular brands