manualshive.com logo in svg

ILMOR MV10 650, Owner'S Manual, Page: 74 / 78

Share
Download
ILMOR MV10 650 Owner'S Manual Download Page 74

SECTION 10

 ILMOR HIGH-PERFORMANCE OWNER’S MANUAL

10-2

Ilmor High-Performance Marine, LLC 

© 7/2013, Version 1.0

Problem  

Possible Cause  

Potential Solution

Engine turns over,  

but will not start. 

(Continued)

No fuel to the engine.

See authorized Ilmor High-
Performance Marine service 
center.

Vapor Lock.

Open engine compartment, run 
bilge blowers, key ignition on for 
5 seconds, then key off (repeat 5 
times), check fuel level.

Clean Power/Clean Ground not 
connected.

Connect Clean Power/Clean 
Ground to the correct engine 
battery.

Engine misses or idles 

rough.

Fouled spark plugs.

Have dealer replace the spark 
plugs.

Loose or defective high-tension leads.

Have dealer tighten or replace 
the high-tension leads.

Weak ignition coil.

Have dealer replace the ignition 
coil.

Vacuum leak.

Check breather hoses/tubes.

Clean Power/Clean Ground not 
connected.

Connect Clean Power/Clean 
Ground to the correct engine 
battery.

Poor boat performance.

Fouled spark plugs.

Have dealer replace the spark 
plugs.

Contaminated fuel.

Drain fuel properly and have 
dealer replace the filter.

Plugged air filter/spark arrestor.

Replace the air filter/spark 
arrestor.

Weak ignition coil.

Have dealer replace the ignition 
coil.

Fuel filter clogged.

Have dealer replace the fuel filter.  

Summary of Contents for MV10 650















































































Reviews:

No comments