ILMOR MV10 650 Owner'S Manual Download Page 62 | Manualshive

Page: 62 / 78

background image

SECTION 8

ILMOR HIGH-PERFORMANCE OWNER’S MANUAL

8-2

Ilmor High-Performance Marine, LLC

© 7/2013, Version 1.0

FUEL SYSTEM TREATMENT

Boats that are going to be stored for extended periods (more than one

month) or winterized should have the fuel systems prepared according to

the boat manufacturer’s instructions.

WARNING!

Always follow the boat manufacturer’s instructions on how

to properly winterize the fuel tank prior to storage.

A fuel stabilizer, such

as STA-BIL, may also be used during long-term storage and winterization

of the engine. Follow the directions provided by the stabilizer’s

manufacturer.

NOTICE: Always perform the proper storage procedures when
storing the boat. Extended storage with fuel in the system can
affect fuel stability and may require system inspection and fuel filter
replacement when the boat returns to service. Fuel systems on all
boats equipped with Ilmor High-Performance Marine engines MUST
be properly prepared for storage periods exceeding 30 days. Owners
are encouraged to seek assistance from an authorized Ilmor High-
Performance Marine service center to properly prepare the drive train
for periods of inactivity exceeding one month. Damage due to improper
storage and/or winterization preparations is not covered under warranty.

OIL STORAGE/WINTERIZATION

Contaminants in used oil can cause engine damage during storage.

Perform an oil change and run the engine to operating temperature to

allow new oil recirculation.

«
...
60
61
62
63
64
...
»

Summary of Contents for MV10 650















































































Reviews:

No comments

Related manuals for MV10 650

Brand: Sachs Pages: 75

Brand: NOVAK Pages: 2

Brand: Kohler Pages: 85

Brand: ABB Pages: 215

Brand: Toyama Pages: 44

Brand: Volvo Penta Pages: 20

Brand: Volvo Penta Pages: 35

Brand: Volvo Penta Pages: 45

Brand: Volvo Penta Pages: 50

Brand: Volvo Penta Pages: 68

Brand: Volvo Penta Pages: 74

Brand: BAFANG Pages: 6

Brand: Clinton Pages: 24

Brand: Lycomin Pages: 171

Brand: PIREZ Pages: 26

Brand: LONCIN Pages: 49

Brand: Briggs & Stratton Pages: 11

Brand: Tecno Automazione Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands