background image

19

UK

10  Operation

10.1  Function check

After power-on the device is in the operating mode� It carries out its measurement 

and evaluation functions and generates output signals according to the set 

parameters�

 

Check whether the unit operates reliably�

10.2  Operating and diagnostic messages via IO-Link 

IODD and IODD descriptive text as a pdf file at: → www.ifm.com

10.3  Operating indication by LEDs

The following indications refer to the factory settings� In this state OUT1 = Hno 

and OUT2 = Hnc� 

Both yellow LEDs (LED1 and LED2, 

→ 8) indicate the switching status of output 

OUT1�

Operating status

LED1 

(yellow)

(OUT1)

LED2 

(yellow)

(OUT1)

LED3 

(green)

(Operating 

voltage)

Unit ready for operation, no medium 

detected

OFF

OFF

ON

Unit ready for operation, medium 

detected

ON

ON

ON

No operating voltage / operating voltage 

too low

OFF

OFF

OFF

Short circuit OUT1

flashes at 4 Hz

ON

Short circuit OUT2

flashes at 4 Hz

ON

Error / failure

OFF

OFF

flashes at 

8 Hz

Visual indication for localisation

 

1 Hz double flashing

ON

Teach operation

(→ 9.1)

Fault during the teach operation

8 Hz yellow/green flashing for 2 s

Teach with locked unit 

(→ 9.1.1)

X

X

flashes at 

1 Hz

X: according to level

Summary of Contents for LI513 Series






















Reviews: