background image

11

UK

8  Operating and display elements

1

1

2

3

On delivery, the two yellow LEDs (LED1 and LED2) indicate the switching 

status of output OUT1� This can be configured via IO-Link 

(→ 9.2.4)

Fig� 1: view of the unit

1: inductive teach button

Fig� 2: top view

1: LED1 (yellow) = switching status OUT1

2:  LED2 (yellow) = switching status OUT1 

(OUT2)

3: LED3 (green) = operating status

The inductive teach button is actuated with a metal object (e�g� a 

screwdriver 1 x 5,5 mm) by applying it flat to the teach surface.

 

No operation is triggered by actuating the button briefly (less than 1 s) or 

continuously (longer than 30 s) (static activation)! 

9  Parameter setting

On delivery, the unit is set to detecting water-based media (e.g. coolant emulsion). 

In many cases the factory setting is sufficient, so that no further settings are 

required�

 

► Check the function by performing an application test) (→ 10)

In case the factory settings are not sufficient:

 

Adapt the unit to the application� 

The unit can be parameterized using the inductive teach button 

(→ 9.1)

 or 

via IO-Link 

(→ 9.2)

� Some functions are only available via IO-Link�

Summary of Contents for LI513 Series






















Reviews: