background image

17

UK

SP2 (FH2) - TEMP

Switch point 2 or upper temperature limit for window function 

([SEL2]=[TEMP]).

[SP2 (FH2)] must be greater than [rP2 (FL2)]. 

 

If [SP2 (FH2)] is set to a value below [rP2 (FL2)], this is 

rejected by the device software�

rP2 (FL2) - TEMP

Switch point 2 or lower temperature limit for window function 

([SEL2]=[TEMP]).

dS1 / dS2

Switching delay

4

) for OUT1 and OUT2.

 

Setting range 0�0���10�0 s

dr1 / dr2

Switching delay

4

) for OUT1 and OUT2.

 

Setting range 0�0���10�0 s

FOU1 / FOU2

Response of OUT1 or OUT2 in case of a fault:

[OFF] = switching output switches OFF in case of a fault�

[On] = switching output switches ON in case of a fault�

[OU] =  switching output reacts according to process value,  

if possible�

Lo�T

Minimum value memory for the temperature

Hi�T

Maximum value memory for the temperature

Unit locking�

Local parameter setting

[Open] = parameter setting via teach button is permitted�

[Locked] = parameter setting via teach button is locked�

1)

 This setting is not possible in combination with [ou2] = [Fno] or [Fnc]� 

2

) This setting is only possible in combination with [SEL2] = [TEMP].

3

) Tap water in grounded metal tank

4)

  Response according to VDMA� According to VDMA the switch-on delay always has an 

effect on SP, the switch-off delay always on rP irrespective of whether the normally open or 

normally closed function is used�

Summary of Contents for LI513 Series






















Reviews: