IFM JN2101 User Manual Download Page 26

Page: 26 / 26

Inclination sensor JN

12 Maintenance, repair and disposal

The unit is maintenance-free.

►

Dispose of the device in accordance with the national environmental

regulations.

13 Approvals/standards

The CE declarations of conformity and approvals can be found at www.ifm.com.

14 Factory setting

SDO

index

Sub-

index

Type

Value

Delivery

0x2000

0x0

Node ID

0x2001

0x0

u16

Baud rate

125 Kbits

0x2040

0x0

Flag for quadrant correction

1: corresponds to "± 180°"

0x2041

0x0

Flag for heating

1: corresponds to "heating on"

0x2042

0x0

Index teach value of the X/Y/Z

axes

2: corresponds to "absolute

measurement"

0x2043

0x0

FIR filter angle

2: corresponds to "FIR lowpass

5Hz"

0x2044

0x0

Angle calculation

0: corresponds to "perpendicular"

0x2045

0x0

CAN 120 Ω terminating resistor

1: corresponds to "activated"

0x2046

0x0

Set zero point of the X/Y axes

2: corresponds to "absolute

measurement"

0x6000

0x0

u16

Resolution

10d: corresponds to "0.01°"

Summary of Contents for JN2101



























Search results

Summary of Contents for JN2101

Reviews:

IFM JN2101, User Manual, Page: 26 / 26

Search results

Summary of Contents for JN2101

Reviews: