IFM Electronic OPD100 Operating Instructions Manual Download

Page: 31 / 39

11.2 Parameter level extended functions

In the parameter level extended functions the following parameters can be selected:

Parameter

Description

[

Factory Reset

]

Reset all parameters to factory setting

►

Confirm the parameter with [ENTER] and select one of the

options [NO] / [YES] using the [Up] or [Down] button�

►

Select [Yes] and confirm with [ENTER]�

> The sensor resets all parameters to factory setting and

changes to the "Guided Teach"�

[

Device Info

]

Sensor information

►

Confirm the parameter with [ENTER] and navigate through the

information lines using the [Up] or [Down] button�

[

Configuration

]

Configuration of the operating mode and the switching

outputs

(→ 11.2.1)

►

Confirm the parameter with [ENTER]�

> The display changes to the configuration settings�

►

Select one of the following options using the [Up] or [Down]

button�

1� [Trigger Mode]

2� [Trigger Source]

3� [Trigger Delay]

4� [Integration Time]

5� [Output Function]

6� [Output Logic]

7� [Back]

[Display]

Configuration of the display

►

Confirm the parameter with [ENTER]�

> The display changes to the display settings�

►

Select one of the following options using the [Up] or [Down]

button�

1� [Brightness]

2� [Colour]

3� [Language]

4� [Back]

[Back]

Finish parameter setting

►

Confirm the parameter with [ENTER]�

> The display changes to menu level 1�

Summary of Contents for OPD100








































Search results

Summary of Contents for OPD100

Reviews:

Related manuals for OPD100

Brands by name

Popular brands

IFM Electronic OPD100, Operating Instructions Manual

Search results

Summary of Contents for OPD100

Reviews:

Related manuals for OPD100

Brands by name

Popular brands