IEMCA Master 80 UP HyperFlexible Page 12 Manual For Use And Maintenance Download | Manualshive

Page: 12 / 190

background image

EN

1 - GENERAL INFORMATION

Master 80 UP HyperFlexible

1 - Pag. 2 / 2

The operations described in the sections that are preceded by this symbol must be

performed by qualified and skilled personnel with specific abilities and precise technical
competence only.

Any other operation can be performed either by qualified personnel and/or by
professional bar feeder operators.

Before carrying out any operation on the bar feeder, it is of the utmost

importance to read this manual carefully.

1.1 WARRANTY

CONDITIONS

The applicable warranty period is subordinated to a correct assembly and coupling of the bar
feeder to the lathe. In particular, prior to the first start-up, accurately make sure that the bar
feeder is correctly aligned with the lathe and fixed with the expansion plugs as shown in
chapter 4.

The product warranty is valid only if the bar feeder is
installed by an authorized technician with Original
Installation Certificate.
Please ask the technician who will make the installation to
show the certificate, in order to ascertain the quality of the
technical operations being carried out.
The warranty shall begin from the date on the “Installation
Certificate” duly filled in and signed.
The document must be sent by mail to:

TECHNICAL SERVICE DEPARTMENT
IEMCA division of IGMI spa
48018 Faenza (Ra) ITALY - Via Granarolo, 167

«
...
10
11
12
13
14
...
»

Summary of Contents for Master 80 UP HyperFlexible































































































































































































Reviews:

No comments

Related manuals for Master 80 UP HyperFlexible

Brand: Federal Signal Corporation Pages: 12

Brand: J.P. SELECTA Pages: 32

Brand: Labnet Pages: 12

Accublock D1301

Brand: Labnet Pages: 13

Brand: Garden Treasures Pages: 2

Brand: XpressFill Pages: 11

Brand: A.HABERKORN Pages: 28

Brand: uniprox Pages: 3

Brand: A.J.Antunes Pages: 24

Brand: B&G Pages: 2

Brand: Sota Pages: 7

Brand: BH FITNESS Pages: 24

Brand: Best Fitness Pages: 26

Brand: TRX Pages: 2

Brand: KaVo Pages: 70

Brand: GreenTec Pages: 66

Brand: Slick Pages: 2

Brand: Delfield Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands