IEMCA Master 80 UP HyperFlexible Page 75 Manual For Use And Maintenance Download

Page: 75 / 190

4 - HANDLING AND INSTALLATION

Master 80 UP HyperFlexible

4 - Pag. 17 / 17

4.5

LUBRICATION OIL - FILLING

WARNING - CAUTION:

wear personal protections according to

the regulations in force.

• Remove cover (A).
• Pour the oil directly into the tank and check the

level through the relevant indicator (B).

Oil features: Class (C) - CKB 150, quantity 80 l.

4.6 ELECTRICAL

CONNECTION

DANGER - WARNING:

this type of operation should only be entrusted to skilled personnel with precise

technical competence and specific abilities to comply with the applicable

standards and regulations in force. The feeder must be electrically connected to

the lathe, which in turn, must be connected to the electrical installation in

compliance with the applicable regulations in force.

The bar feeder is normally equipped with a multiple plug to be inserted into the special lathe
socket; refer to the "Wiring diagram" if necessary.

Summary of Contents for Master 80 UP HyperFlexible































































































































































































Search results

Summary of Contents for Master 80 UP HyperFlexible

Reviews:

Related manuals for Master 80 UP HyperFlexible

Brands by name

Popular brands

IEMCA Master 80 UP HyperFlexible, Manual For Use And Maintenance

Search results

Summary of Contents for Master 80 UP HyperFlexible

Reviews:

Related manuals for Master 80 UP HyperFlexible

Brands by name

Popular brands