IEMCA Master 80 UP HyperFlexible Page 57 Manual For Use And Maintenance Download | Manualshive

Page: 57 / 190

background image

3 - SAFETY - GENERAL INFORMATION

Master 80 UP HyperFlexible

EN

3 - Pag. 13 / 13

3.9 FORESEEABLE

MISUSES

• Do not tamper with the machine's safety devices (for example, the safety microswitches of

the openable guard to access the bar magazine)

• Do not use the lubrication pump for other purposes (for example, to pour different liquids)
• Do not use the oil tank for other purposes and do not pour into it liquids or substances

different from those recommended by the manufacturer

•  Do not load bars made of flammable materials
•  Do not load bars with a greater straightness than the one recommended by the manufacturer
•  Do not load bars with sizes or shapes different than those recommended by the

manufacturer

• Do not interfere with any body part on the bar feed axis
• Do not approach the bar feeder with open flames or very hot objects (for examples,

cigarettes). Danger of oil flammability.

• Do not draw electricity or pneumatic energy from the bar feeder to power other machines or

tools

• Keep hands out of the remnant recovery zone. Residual risks of upper limbs crushing! (Risk

due to remnant drop and clamp device).

• The magazine having no guards, it is forbidden to climb on it.
• Keep your limbs out of the bar feeding magazine zone when near the elevators. Residual

risks of elevator downward slipping leading to limb crushing!

«
...
55
56
57
58
59
...
»

Summary of Contents for Master 80 UP HyperFlexible































































































































































































Reviews:

No comments

Related manuals for Master 80 UP HyperFlexible

Brand: K&K Pages: 8

Brand: NAD Pages: 10

Brand: Tascam Pages: 8

Brand: B-K lighting Pages: 5

Brand: B-K lighting Pages: 4

Brand: B-K lighting Pages: 3

Brand: ECE Pages: 2

Brand: Ecco Pages: 5

Evolution Series

Brand: Bakare Pages: 38

Brand: Hakko Electronics Pages: 8

Professional HS 8

Brand: Hailo Pages: 5

Brand: Hainbuch Pages: 52

Brand: MAGIC FX Pages: 25

Frontier FC5706

Brand: OHAUS Pages: 47

Brand: Ocutech Pages: 4

Brand: Yacht Devices Pages: 32

Brand: Cablexpert Pages: 12

Brand: Orliman Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands