IEMCA Master 80 UP HyperFlexible Page 138 Manual For Use And Maintenance Download

Page: 138 / 190

9 - PART REPLACEMENT

Master 80 UP HyperFlexible

9 - Pag. 2 / 2

9.1

FEEDING CHAIN – REPLACEMENT

The replacement of the feeding chain is a very complex operation; contact IEMCA service
department.

9.2

ELEVATOR CARRIAGE DRIVE SAFETY JOINT - REPLACEMENT

• Slacken the drive chain:
• Remove ring nut (A) and extract in order: spring

(B), washer (C), bearing (D), pinion (E).

• Remove ring nut (F) and extract in order: shaft

(G), flange (H).

• Reassemble all components in the inverted

order, replacing the worn flange (H) and pinion
(E) with the new ones.

• Tension the chain.

Summary of Contents for Master 80 UP HyperFlexible































































































































































































Search results

Summary of Contents for Master 80 UP HyperFlexible

Reviews:

Related manuals for Master 80 UP HyperFlexible

Brands by name

Popular brands

IEMCA Master 80 UP HyperFlexible, Manual For Use And Maintenance

Search results

Summary of Contents for Master 80 UP HyperFlexible

Reviews:

Related manuals for Master 80 UP HyperFlexible

Brands by name

Popular brands