IEMCA BOSS 338 HD Manual For Use And Maintenance Download Page 76

Page: 76 / 214

4 - HANDLING AND INSTALLATION

Boss 338HD - 552HD

4 - Pag. 16 / 16

4.4.7 Telescopic front nose - Installation

If the bar feeder is equipped with a telescopic front
nose, proceed as described below.

• Remove the fixed front nose that had been

installed to obtain alignment between the bar
feeder and the lathe.

• Fix the flange "A" (a general example is shown

in the figure).

INFORMATION:

the lathe spindle front nose "B" should

not turn. If it does, a support or another

similar device should be fitted to

prevent telescopic front nose turning

after it has been installed.

• Move the headstock to its "completely

backwards" position and measure the value "L".
Take out the grub screw "C", press the
telescopic front nose to its limit stop minus 5
mm and cut the pipe "D" to the measured value.

• Move the headstock to its "completely forwards"

position. Remove the cover "E", install the front
nose in the flange "F" and place back the cover "E".

• Check smooth sliding of the telescopic front nose by moving the headstock forwards and

backwards.

DANGER - WARNING: Please, note that, by removing the telescopic front nose,

the bar feeder might be DANGEROUS to the operator and/or installation

technician due to bar pusher extension.

Summary of Contents for BOSS 338 HD























































































































































































































Search results

Summary of Contents for BOSS 338 HD

Reviews:

Related manuals for BOSS 338 HD

Brands by name

Popular brands

IEMCA BOSS 338 HD, Manual For Use And Maintenance

Search results

Summary of Contents for BOSS 338 HD

Reviews:

Related manuals for BOSS 338 HD

Brands by name

Popular brands