manualshive.com logo in svg

IEMCA BOSS 338 HD, Manual For Use And Maintenance, Page: 95 / 214

Share
Download
IEMCA BOSS 338 HD Manual For Use And Maintenance Download Page 95

 

5   -   ADJUSTMENTS AND SETUP 

Boss 338HD - 552HD 

EN 

 

5 - Pag. 3 / 3 

 

5.2 

GENERAL ADJUSTMENTS - FOREWORD 

 

All the necessary adjustments for correct bar feeder operation are included. They may become 
necessary for maintenance, troubleshooting or component replacement. 
 
 

5.2.1  Feeding chain - Adjustment 

For the movement chain of the bar pusher, tension 
screws A on the rear plate of bar feeder is provided. 
After some bar feeder operating hours, the chain 
tension has to be checked. 
•  If bush B of chain tension is still fastened to the 

rear plate, then no chain extension took place. 

•  On the contrary, if bush B moved away by 1- 2 

mm from rear plate, then a chain extension took 
place, which is dangerous for correct operation of 
bar feeder. Screw A must then be tightened until 
bush B is fastened to the rear plate. 

 

5.2.2  Air adjusting unit - Adjustment 

After unscrewing the glass protection, the 
pressure switch can be properly adjusted by 
turning the relevant adjusting screw (G). Proper 
setting is 4.5 bars (0.45 MPa). 
 

 WARNING - CAUTION: 

 

Do not further turn anticlockwise when 

the green pointer is on 0. This may 

cause damage to the pressure switch. 

 

 INFORMATION: 

 

Lubricator D is fitted only when the 

headstock synchronization device is 

assembled. 

 

 

 

Summary of Contents for BOSS 338 HD























































































































































































































Reviews:

No comments