IEMCA BOSS 338 HD Manual For Use And Maintenance Download Page 49 | Manualshive

Page: 49 / 214

IEMCA BOSS 338 HD Manual For Use And Maintenance Download Page 49

3 - SAFETY - GENERAL INFORMATION

Boss 338HD - 552HD

EN

3 - Pag. 3 / 3

3.2

HANDLING AND INSTALLATION - Safety

• The bar feeder must be handled using suitable means and methods only.

• Do not stand or transit underneath a suspended load, or within the range of action of the

crane, lift truck or other suitable lifting and transport means.

• The bar machining and loading area must be delimited to prevent collisions between the

operator and the means of transport or handling of the material to be machined or of other
kinds.

• Correct positioning of the bar feeder, lighting and cleanliness of the working environment

are of the utmost importance for personal safety.

• The connection to the electrical installation must be carried out by skilled personnel only.

• Make sure that the electrical installation is connected to an efficient earthing system by

means of an appropriate cable.

3.3

ADJUSTMENTS AND SETUP - Safety

• Carry out the adjustments as described in the operation manual.

• Do not change the machining parameters to obtain performances other than those envisaged

in the design and testing phases.

• Do not adjust the bar feeder when it is running, unless expressly requested in the manual.

• Do not feed the machine with bars of dimensions other than those recommended by the

manufacturer.

• Do not use hoses as handholds.

«
...
47
48
49
50
51
...
»

Summary of Contents for BOSS 338 HD























































































































































































































Reviews:

No comments