IEM Tel-O-Graph BT Instructions For Use Manual Download Page 37 | Manualshive

Page: 37 / 54

background image

Cleaning and disinfection

37

DE

EN

9

Cleaning and disinfection

WARNING

▪

When putting the blood pressure monitor on, there must no longer be any disinfectants on the blood
pressure cuff!

▪

There are patients who have intolerances (e.g. allergies) to disinfectants or its components!

ATTENTION

▪

Do not immerse the cuff with balloon and blood pressure monitor in disinfectant, water or other liquids!

▪

If liquid nevertheless penetrates the device, switch it off immediately and send it away to be checked by
the manufacturer or healthcare provider/physician!

▪

Do not open the housing of the Tel-O-Graph

®

BT, otherwise any warranty becomes void.

Note

Always observe the manufacturer's instructions on the disinfection and cleaning of these products.

«
...
35
36
37
38
39
...
»

Summary of Contents for Tel-O-Graph BT























































Reviews:

No comments

Related manuals for Tel-O-Graph BT

Brand: Abus Pages: 50

Brand: Abus Pages: 50

Brand: IC Sciences Pages: 2

Brand: Radiforce Pages: 48

Brand: Wacom Pages: 32

Brand: Vidikron Pages: 76

Brand: PanelPilot Pages: 10

Brand: Gator Pages: 6

Brand: iHealth Pages: 210

Brand: voxicon Pages: 11

Brand: VTech Pages: 2

Brand: VTech Pages: 18

Optiquest 1782DC

Brand: ViewSonic Pages: 63

Brand: Neway Pages: 13

Brand: Symphony Pages: 7

VX710 - 17" LCD Monitor

Brand: ViewSonic Pages: 78

Brand: Hisense Pages: 33

Brand: Feelworld Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands