IEI Technology KINO-LX User Manual Download Page 91

Page: 91 / 197

Page 91

KINO-LX Motherboard

5.1.2 Using Setup

Use the arrow keys to highlight items, press

NTER

to select, use the

AGE

and

AGE

OWN

keys to change entries, press

for help and press

to quit. Navigation

keys are shown below.

Key

Function

Up arrow

Move to the item above

Down arrow

Move to the item below

Left arrow

Move to the item on the left hand side

Right arrow

Move to the item on the right hand side

+/Page up

Increase the numeric value or make changes

-/Page down

Decrease the numeric value or make changes

Esc

Main Menu – Quit and do not save changes into CMOS

Status Page Setup Menu and Option Page Setup Menu --

Exit current page and return to Main Menu

General help, only for Status Page Setup Menu and Option

Page Setup Menu

F2 Item

help

Previous values for the page menu items

Fail-safe defaults for the current page menu items

Optimized defaults for the current page menu items

Menu in BIOS

F10

Save changes and Exit BIOS

Table 5-1: BIOS Navigation Keys

5.1.3 Getting Help

When

is pressed a small help window describing the appropriate keys to use and the

possible selections for the highlighted item appears. To exit the Help Window press

the

key again.

Summary of Contents for KINO-LX






































































































































































































Search results

Summary of Contents for KINO-LX

Reviews:

IEI Technology KINO-LX, User Manual, Page: 91 / 197

Search results

Summary of Contents for KINO-LX

Reviews: