IEI Technology KINO-LX User Manual Download Page 115

Page: 115 / 197

Page 115

KINO-LX Motherboard

Disabled

Block mode is not supported.

Enabled

(Default)

Block mode is supported.

Onboard FDC Controller [Enabled]

Use the

Onboard FDC Controller

option to enable or disable the onboard floppy

controller. If the system is not connected to a floppy disk or uses an adapter for the FDD,

this option can be disabled.

Disabled

The FDD controller is disabled.

Enabled

(Default)

The FDD controller is enabled.

Onboard Serial Port 1 [3F8/IRQ4]

Use the

Onboard Serial Port 1

option to select the I/O address and IRQ for the onboard

serial port 1. The serial port can be disabled or the I/O address and the IRQ can be

automatically selected by the BIOS. The

Onboard Serial Port 1

options are:

Disabled

3F8/IRQ4 (Default)

2F8/IRQ3

3E8/IRQ4

2E8/IRQ3

Auto

Summary of Contents for KINO-LX






































































































































































































Search results

Summary of Contents for KINO-LX

Reviews:

IEI Technology KINO-LX, User Manual, Page: 115 / 197

Search results

Summary of Contents for KINO-LX

Reviews: