IEI Technology KINO-LX User Manual Download Page 122

Page: 122 / 197

Page 122

IEI® Technology, Corp

KINO-LX Motherboard

5.7 PnP/PCI Configurations

Use the PnP/PCI Configurations menu (

BIOS Menu 9

) to set the plug and play, and PCI

options.

BIOS Menu 9: PnP/PCI Configurations

PNP OS Installed [No]

The

PNP OS Installed

option determines whether the Plug and Play devices connected to

the system are configured by the operating system or the BIOS.

(Default) If the operating system does not meet the Plug and Play

specifications, BIOS configures all the devices in the system.

Yes

Set this option if the system is running Plug and Play aware

operating systems. The operating system changes the

interrupt, I/O, and DMA settings.

Reset Configuration Data [Disabled]

Use the

Reset Configuration Data

option to reset the Extended System Configuration

Data (ESCD) when exiting setup if booting problems occur after a new add-on is installed.

Summary of Contents for KINO-LX






































































































































































































Search results

Summary of Contents for KINO-LX

Reviews:

IEI Technology KINO-LX, User Manual, Page: 122 / 197

Search results

Summary of Contents for KINO-LX

Reviews: