IEI Technology KINO-LX User Manual Download Page 123

Page: 123 / 197

Page 123

KINO-LX Motherboard

Disabled

(Default)

ESCD will not be reconfigured

Enabled

ESCD will be reconfigured after you exit setup

Resources Controlled By [Auto (ESCD)]

Use the

Resources Controlled By

option to either manually configure all the boot and

plug and play devices, or allow BIOS to configure these devices automatically. If BIOS is

allowed to configure the devices automatically IRQs, DMA and memory base address

fields cannot be set manually.

Auto(ESCD)

(Default)

BIOS automatically configures plug and play devices as

well as boot devices.

Manual

Manually configure the plug and play devices and any

other boot devices.

x IRQ Resources [Press Enter]

The IRQ Resources option (

BIOS Menu 10

) can only be selected if the Resources

Controlled By option is set to Manual.

BIOS Menu 10: IRQ Resources

Summary of Contents for KINO-LX






































































































































































































Search results

Summary of Contents for KINO-LX

Reviews:

IEI Technology KINO-LX, User Manual, Page: 123 / 197

Search results

Summary of Contents for KINO-LX

Reviews: