IEI Technology KINO-LX User Manual Download Page 185

Page: 185 / 197

Page 185

KINO-LX Motherboard

Figure E-2: RAID BIOS Setup Utility

Step 7:

Step 8:

Configure the RAID settings

. Use the

RAID BIOS Setup Utility

Figure E-2

to configure the RAID array. Brief descriptions are given below.

Install the OS

. After the RAID array has been configured (see below) install the

OS. To do this, please refer to the documentation that came with the OS.

Step 0:

E.4 RAID Options:

E.4.1 Create RAID 0 Striping for Performance

WARNING!

All data previously stored on the member drives of a RAID configuration are

destroyed during the RAID initialization process. If “used” drives are used to

create a RAID array, make sure the data has been moved or backed up

before creating a RAID array out of the disk drives.

Summary of Contents for KINO-LX






































































































































































































Search results

Summary of Contents for KINO-LX

Reviews:

IEI Technology KINO-LX, User Manual, Page: 185 / 197

Search results

Summary of Contents for KINO-LX

Reviews: