manualshive.com logo in svg

IEI Technology KINO-LX, User Manual, Page: 81 / 197

Share
Download
IEI Technology KINO-LX User Manual Download Page 81

 

 

Page 81

 

KINO-LX Motherboard

4.5.4 LCD Backlight Installation 

To connect an LCD backlight (inverter) to the motherboard, follow the instructions below. 

Step 1: 

Step 1: 

Step 1: 

Step 1: 

Connect the 5-pin connector end of the LCD backlight cable to the CN12 header 

on the motherboard. A keyed pin on the connector prevents it from being 

connected incorrectly.

Step 0:

 

4.5.5 Power Connection 

To connect the motherboard to a power supply, follow the instructions below. 

Connect a 20-pin AT/ATX power connector from a power supply to the CN19 

power connector on the motherboard. A keyed pin on the connector prevents it 

from being connected incorrectly.

Step 0:

 

4.5.6 LVDS LCD Installation 

To connect a LVDS LCD to the motherboard, follow the instructions below. 

Connect the 20-pin connector end of a TTL LCD cable to the CN13 miniature 

crimping connector on the motherboard. A keyed pin on the connector prevents 

it from being connected incorrectly.

Step 0:

 

4.5.7 TTL LCD Installation 

To connect a TTL LCD to the motherboard, follow the instructions below. 

Connect the 40-pin connector end of a TTL LCD cable to the CN11 miniature 

crimping connector on the motherboard. A keyed pin on the connector prevents 

it from being connected incorrectly.

Step 0:

 

Summary of Contents for KINO-LX






































































































































































































Reviews:

No comments