manualshive.com logo in svg

IEI Technology IMBA-9454B, User Manual

Share
Download
IEI Technology IMBA-9454B User Manual Download Page 30

 

 

IMBA-9454B ATX Motherboard 

Page 14 

All serial ports support the RS-232 communication protocol only. 

2.9.3 Super I/O 

The iTE IT8718F Super I/O chipset is connected to the Intel® ICH7 Southbridge through 

the LPC bus. The iTE IT8718F is connected to the interfaces listed in the subsections 

below. 

2.9.3.1 Enhanced Hardware Monitor 

The Super I/O Enhanced Hardware Monitor monitors all the thermal and voltage inputs. 

These are reported to the BIOS and can be seen in the BIOS hardware health 

configuration menu. 

2.9.3.2 Fan Speed Controller 

The fan speed controller allows the fan speeds to be controlled. One of the pins connected 

to the fan sends the fan speed information that is then relayed to the BIOS. 

2.9.3.3 Parallel Port 

The Super I/O parallel port (LPT) supports standard mode, enhanced mode and 

high-speed mode parallel port devices. The LPT is compliant with the following LPT 

modes. 

2.9.3.4 Keyboard and Mouse Controller 

The Super I/O keyboard controller can execute the 8042 instruction set.   

2.10 Environmental and Power Specifications 

This section outlines the system environmental and power specifications. 

2.10.1 System Monitoring 

The IMBA-9454B monitors the following thermal inputs: 

ƒ

 System 

temperature 

ƒ

 Power 

temperature 

ƒ

 CPU 

temperature 

Summary of Contents for IMBA-9454B

































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands